Cycle News is a weekly magazine that covers all aspects of motorcycling including Supercross, Motocross and MotoGP as well as new motorcycles
Issue link: https://magazine.cyclenews.com/i/127940
RIDING
IMPRESSION~
.......
~
0...
~
34
How so?
"We could overfill the combustion
chamber during the intake stroke, trap a
small portion of the mixture in the first
two or three inches (50-75mm) of the
exhaust pipe, then use back pressure to
force it back in just before the upper piston closes off all the ports. This could
add significant performance, but it's an
area I haven't experimented in - yet."
Well, leaving aside the difficulty of
calculating the six-stroke's engine capacity on an equivalency basis so it can go
racing (the Norton rotary suffered a
comparable problem), the Beare BEARS
bike gives a taste of what's in store
when he does so. Riding it at Calder for
a dozen laps brought to light three sig-.
nificant assets of the six-stroke engine
and one, maybe two negatives - one of
those being the unreasonably loud
exhaust noise, on which I'll reser;ve
judgment, but it appears not to be an
issue. The other question mark was over
the power curve. While there's no doubt
it revs reasonably high by four-stroke
standards, there seemed to be no direct
benefit in doing so - there was no more
power up high at, say, 8000 rpm than
there seemed to be 2000 revs lower. Malcolm Beare says this is a function of
cylinder porting and perhaps fuel mixture - the old two-stroke imponderables,
here applied to a four-stroke-based
motor.
After the test, he discovered that the
Mikunis were underjetted, and also
believes the engine is overcarbureted - a
theory I'd go along with, especially
given the difficulty of balancing two
carbs per cylinder correctly. He says
he'd also like to play around with the
porting. But Malcolm Beare has so far
concentrated - in the time available after
grazing his cattle and getting in the harvest! - on proving the essential worth of
his six-stroke concept, and refining its
basic application.
Now that he's built the racer (and
enlisted noted four-stroke rider Phil
Payne to help develop it), he can worry
about the performance angle. One thing
he certainly doesn't need to worry about
is torque, which together with the crisp,
responsive throttle pickup and the
reduced vibration - even compared to a
smooth-action 90-degree V-twin - are
the three strong points of the six-stroke
_
motor. The Beare engine is unbelievably
muscular in terms of torque, and from
very low revs, too.
Ironically, you especially appreciate
this because Malcolm's evident talents
as a bush engineer are not matched by
those of a tube-bender: The square-tube
nickel-steel chassis is pretty awful in
terms of handling, especially with a pair
of oversprung Koni shocks at the rear.
The stQck Ducati frame would have
been a better bet, except on tha t you
need to drop the engine out to remove
the top end of the rear cylinder, which
you can't do even with the original
desmo cylinder head in place, let alone
the wider Beare arrangement.
But the fact that the bike jumps
around over bumps and doesn't steer
very well actually helps you appreciate
the engine's responsiveness, because
you may need to back off the throttle in,
say, the middle of the Calder chicane to
allow the chassis .to recover its poise especially if leaning it over further to the right to get out of trouble might make
you start worrying about grounding the
lower carb on the front cylinder when
you did so!
But when you then get on the gas
again, get ready for a surprise: Not only
is there instant response when you twist
the wrist, there's tractor-pulling torque
at seemingly whatever revs the engine's
turning over at - even as low as what
felt like 2000-3000 rpm or so. (There's no
tachometer fitted, bu t having ridden the
odd Ducati V-twin down the years, I
may claim to have a rev-sensitive seat of
the pants.)
There's also no transmission sna tch
at very low revs, indicating a responsive, torquey motor, while the way it
pulls hard from way down low bears all
the hallmarks of a long-stroke engine
design, whereas the opposite is, in fact,
the case: The lower "four-stroke" crankshaft assembly has 86 x 57mm dimensions, while the upper "two-stroke"
ones measure 60 x 25mm.
Yet the inherent nature of the Beare
motor is one of a torquey slugger, belying these measurements. And allied
with the so-responsive pickup and a
wide spread of usable power, this
makes the bike ridiculously easy to ride
• - you hardly need to use the gearbox "at
all; just park it in top gear and ride it
(Left) Oesigner-builder Malcoim Beare with a model of his unusual powerplant.
(Above) While Beare's mechanical genius is evident in the powerplant design, the chassis
that he also bulit leaves a bit to be desired. Thankfully the engine is very torquey, with
crisp throttle response, making It easy to get yourself out of trouble.
like a semiautomatic. Even backing off
the throttle in the middle of a turn to let
the chassis straighten up and fly right
doesn't require you to drop down a gear
- just Crack it open when you're ready,
feel the front wheel start to lift on you,
and - drive.
My hands-on assessment of the
Beare six-stroke leads to some
inescapable conclusions, one of which is
that in its present form, this isn't a performance concept. There doesn't seem
to be the power on tap that the dyno
charts s

