Cycle News - Archive Issues - 1980's

Cycle News 1980 03 19

Cycle News is a weekly magazine that covers all aspects of motorcycling including Supercross, Motocross and MotoGP as well as new motorcycles

Issue link: https://magazine.cyclenews.com/i/126461

Contents of this Issue

Navigation

Page 30 of 71

o 00 0') The Pro Circuit pipe helped mid-range and top end performance. However, it is not enduro legal. Husqvama 125 CR Project Bike 125 Cft suggested retail Lectron Carburetor Windsor Tank Pro Circuit Pipe Magura Levers Pro Circuit Side Covers VDO Pacer Kit CIainHnont Digital Clock Clairernont Route Sheet Holder Husky Products Ughting Kit Red Dot FrontT"e skill) test rider used the Husky for. The stock Ohlins shocks provided the best working production rear suspension we have tested. The amount of rear wheel travel equals that at the front· U.8 inches. At first, the shocks gave a bit of a stiff ride but after a few hours we couldn't fault the units. No shock fade could be detected at any time under any riding can· ditions. The shock reservoirs work. For fine tuning the damping which can be adjusted for both rebound and compression. Harsh bottoming is prevented wirh the use of rubber bumpers. VariQus springs are avail· able from Ohlins. although we believe most riders will be pleased with the 137/128 lb. stock units. 44 We had heard the oft· repea ted stories about Husky's reponedly poor brakes. The brakes on the 125 CR work. However, die 1980 model does leave room for improvement in '81. Before the bike was ridden, most of the lower adjustment was used up. To our surpnse, alter hair a dozen hare scrambles and enduros, very little more adjustment was required of the front brake. Many bikes would have been into their second set of shoes. Front and rear brakes on the Husky are interchangeable. After just a short period of time the rear brake pedal will wobble in aDd out slightly. and the brake rod will be bent. but this will not hamper its positive action. The brakes are as watenight as most on the market today. So. why does King Richard wbeelie through most water crossings? Guess $1.750.00 99.95 46.45 85.00 18.50 24.95 105.00 99.95 19.95 45.00 41.70 Total: $2.336.45 he enjoys it. Now for the powerplant: A displacement of 124cc with enough map to ricochet from corner to corner and yet enough tug for long inclines comes out of the small engine. A near perfect combination. For the type of use we were putting it to, we opted not to modify the engine for the most part. The 1980 125 CR is equipped with a COl Motoplat with an internal rOtor. We switched ours to an external rotor and Motoplat, a stock item from the previous year's model. The external rotor unit helps tone down the powerband a bit, thus making the bike feel a little less pipey. It also allows a lighting kit to be installed· a must for enduro riding. Mitch Payton. of Pro Circuit Products. ended our search for a high performance pipe. The pipe was designed by Rick Asch and is styled after the Husky 250 pipe. Payton refers to it as "the little brother" of the Husky 250 pipe. Installation is rather simple. The stock bracket is used, just raised and turned on the frame. The Pro Circuit snakes around the frame whereas the stock pipe goes straight back. The pipe also mounts on the frame under where the tank and seat meet. A tab is already welded to the frame. although the stock pipe doesn't mount there. We placed a spring - similar to the spring on the front pipe bracket between the Pro Circuit pipe and the frame. This eliminates the possibility of any cracks developing due to vibration. The Pro Circuit pipe tucks under the tank nicely, but pushes against the side cover on the left side. The side cover can be removed and we did. replacing both covers with FIM style covers from Pro Circuit. The shan silencer on the Pro Circuit pipe has just one drawback - a major one for many riders. It's not enduro legal due to its loudness and its lack of a Forestry Department approved spark arrestor. However, the pipe was not designed for enduro use. For enduro use we re·mounted the stock pipe. For hare scramble use. the Pro Circuit pipe really lets the motor wind. It is designed to increase top end and widen mid-range. We feel that mounting a Pro Circuit pipe is the best way to improve power with the exception of radical engine work. While we were on our project spending spree. we decided to try a Lectron carburetor. We had always been told how the Lectron Powerjet smoothed out power, decreased the chances of seizures, and helped torque and top erid. We had heard a lot .. the question was how much was truth and how much was propaganda. While the airbox itself requires no modifications when adding a Lectron carbo both rubber boots must be replaced. We replaced the air boot that connects the airbox to the carb with one off of a Husky 250 (the 390 item is identical). The larger boot fits into the same size hole in the airbOlC We smeared silicone nibber sealer around the edges to seal the airbox. A larger hose clamp is needed to accomodate the large bell on the Lectron and the stock intake boot .. between the carb and jug .. must also be replaced. Many Husky owners have complained about the stock boot cracking or splitting; we replaced it with a longer piece of I ~ inch neoprene hose. Radiator hose can' be used, but may be deteriorated by the fuel flowing through it. Jetting the Lectron was no major problem. A 6-2 needle worked with a 60 main powerjet. The Lectron really helped ease bringing the 125 to life. Staning the stock bike was a bit of a temperamental operation that took some getting used to. With the stock Bing carb, one had to be careful about flooding the engine when cold. We aren't sure how the carb would be for MX use, but the power seems smoother and even wider with the Lectron. The 36mm Lectron's biggest improvement to the bike was the increased top end obtained from it. The Lectron is supposed to help cut fuel consumption, but that wasn't something we were worried about as we replaced the stock 2 gallon tank with a 3 gallon Windsor tank. With the 3 gallon tank we could travel at least 65 miles in any conditions. No modifications were required to mount the tank. The Windsor comes with its own petcock, but the stock Husky gas cap is utilized. For our time keeping in enduros we chose a Clairemont Cycle Supply digital clock. The Clairemonl item comes to life with the press of a button. One thing riders must be constantly aware of is that the clock also has a fast forward button. Two riders we spoke' to complained about their unknowingly advancing the time. So, be forewarned. We found the Clairemonl clock to be very accurate and durable. The time appears in nice large readout numerals. It's held stationary to the bike's crossbar or handlebars with the use of a hose clamp. We purchased ours from Hi-Point Racing Products. Clairemont also produces a superior route sheet holder which is also available through dealers who stock Hi-Point distributed products. With the Clairemonl holder a rider can decipher up to seven lines without having to rotate the tape forward. Constructed of ABS plastic. the holder is virtually unbreakable. A set of unique pressure tabs hold the plexiglass window securely in the recessed frame. The pressure tabs work better than screws because there are no threads to strip or become clogged. The plexiglass window offers no distonion nor magnification. The route sheet holder is fairly watenight, but we found ourselves placing narrow strips of duct tape over the edges for peace of mind through additional waterproofing. The advancement knobs are nice and large and provide for effortless advancing of the rpute sheet. Through Husky Products we obtained a VDO Pacer kit. The kit includes an accurate 24-mph pacer head, a hub drive, cable and mounting bracket. The cable must be 40" long to reach on the CR models. Modification is required of the mounting bracket to use the unit on a 125 CR. We found it to be "accurate as hell" as it kept us on a 24-mph average through several enduros. A light kit from Husky products included a Preston Petty headlight, number plate, taillight and the wiring needed. The tank and seat must be removed for installation which took us approximately 30-minutes. Replacing the headlight bulb with a 12 volt, 55 watt bulb will do away with the blowout problems of the stock bulb. While the stock Trelleborg tires are excellent. we opted to change the 3.50 x 21 front tire because we found it to be tOO wide. We switched to Hi-Point Racing Products' 3.00 x 21 Red Dot tire. We have used other sizes of Red Dot tires and feel that they are the best buy on the market. In short. they provide Metzeler performance at Red Dot prices. In conclusion, we feel that the stock bike is a winner right out of the box. The modifications we made all improved the already winning combination. Each change was made for personal reasons and worked for us. If you feel like it. go for it and modify your own Husky. As for us, we already have and now we're going to quit writing and go riding! •

Articles in this issue

Archives of this issue

view archives of Cycle News - Archive Issues - 1980's - Cycle News 1980 03 19